Start studying Testout 3.4 Motherboard Troubleshooting. Learn vocabulary, terms, and more with flashcards, games, and other study tools. Your computer starts, but the hard disk light does not come on when the system is booting. What is likely the issue?
Your Best Year Ever: College Tech Tips
Introduction![Motherboard Starts But No Image Motherboard Starts But No Image](http://i.imgur.com/QOwpK0O.jpg)
Find Free Books
Tech To Make Life Easier
Connect To Entertainment
Fix It Yourself
The most common way that a computer 'won't turn on' is when the PC actually does power on but doesn't display anything on the monitor.
You see lights on the computer case, probably hear fans running from inside, and may even hear sounds, but nothing at all shows up on your screen.
There are several possible reasons why your monitor isn't displaying information, so it's very important that you step through an ordered process like the one outlined here.
If your computer is, in fact, showing information on the monitor, but is still not booting fully, see How to Fix a Computer That Won't Turn On for a better troubleshooting guide.
How to Fix a Computer That Turns on but Displays Nothing
Fixing a computer with this problem could take anywhere from minutes to hours depending on why exactly the computer isn't displaying anything on the monitor, which we'll figure out as we troubleshoot the issue.
Are you troubleshooting this issue on a computer that you've just built? If so, triple check your configuration! There is a very, very good chance that your computer is not booting up completely due to a misconfiguration and not an actual hardware failure or other problem.
- Before you begin more complicated and time-consuming troubleshooting with the rest of your computer, make sure your monitor is working properly.It's possible that your computer is working fine and your monitor is your only problem.
- Verify that your PC has fully power cycled. In other words, make sure your computer has completely restarted — ensure that it's coming on from a completely powered-off state.Often times a computer will appear to 'not be on' when actually it's just having problems resuming from either the Standby/Sleep or Hibernate power saving mode in Windows.You can power off your computer completely while in a power saving mode by holding the power button down for 3 to 5 seconds. After the power is completely off, turn on your PC and test to see if it will boot normally.
- Troubleshoot the cause of the beep code if you're lucky enough to get one.A beep code will give you a very good idea of exactly where to look for the cause of your computer turning off.If you don't resolve the problem by troubleshooting the specific beep code, you can always return here and continue with the steps below.
- Clear the CMOS.Clearing the BIOS memory on your motherboard will return the BIOS settings to their factory default levels. A BIOS misconfiguration could be why your PC won't start up all the way.If clearing the CMOS does fix your problem, make sure any changes you make in BIOS are completed one at a time so if the problem returns, you'll know which change caused your issue.
- Verify that the power supply voltage switch is set correctly.If the input voltage for the power supply is not correct (based on your country) then your computer might not turn on completely.There's a good possibility that your PC wouldn't power on at all if this switch is wrong but an incorrect power supply voltage might also prevent your computer from starting properly in this way, too.
- Reseat everything possible inside your PC.Reseating will reestablish the various connections inside your computer and is very often a 'magic' fix to problems like this one.Be sure that all the cables are connected correctly. For example, if the onboard video card has been disabled, plugging a VGA cable into it will result in nothing on the monitor even if the computer is powered on. In this case, you'd want to plug the VGA cable into the correct video card.Try reseating the following and then see if your computer begins to display something on screen:Unplug and reattach your keyboard and mouse as well. There isn't a great possibility that the keyboard or mouse is causing your computer to not turn on fully but we might as well reconnect them while we're reseating everything else.
- Reseat the CPU only if you suspect that it might have come loose or might not have been installed properly.We call this out separately only because the chance of a CPU coming loose is very slim and because installing one is a sensitive task. This isn't a big concern if you're careful, so don't worry!
- Check for causes of electrical shorts inside your computer.This is often the cause of the problem when the computer powers off by itself, but certain shorts can also prevent your computer from booting fully or showing anything on the monitor.
- Test your power supply.Just because your computer's fans and lights are working does not mean that the power supply is functioning properly. The PSU tends to cause more problems than any other hardware and is often the cause of a computer not coming on all the way.Replace your power supply immediately if it fails any test you perform.After replacing the power supply, assuming you do, keep your PC plugged in for 5 to 10 minutes prior to turning it on. This provides time for some recharging of the CMOS battery, which may have been drained.We want to make this point very clear — do not skip a test of your power supply thinking that your problem can't be the PSU because 'things are getting power.' Power supplies can work in varying degrees — one that isn't fully functional needs to be replaced.
- Start your computer with essential hardware only. The purpose here is to remove as much hardware as possible while still maintaining your PC's ability to power on.If your computer starts normally with only essential hardware installed, proceed to Step 11.If your computer still isn't displaying anything on your monitor, proceed to Step 12.This step is easy enough for a novice to complete, takes no special tools, and could provide you with a lot of valuable information. This isn't a step to skip if, after all the steps above, your computer is still not turning on completely.
- Reinstall each piece of hardware that you removed in Step 10, one piece at a time, testing after each installation.Since your computer powered on with only the essential hardware installed, those components must work properly. This means that one of the hardware components you removed is causing your PC to not turn on properly. By installing each device back into your PC and testing them each time, you'll eventually find the hardware that caused your problem.Replace the nonworking hardware once you've identified it. These Hardware Installation Videos should come in handy as you're reinstalling your hardware.
- Test your computer's hardware using a Power On Self Test card. If your PC still isn't displaying information on your monitor with anything but essential computer hardware installed, a POST card will help identify which piece of remaining hardware is causing your computer to not come on completely.If you don't have and are unwilling to purchase a POST card, skip to Step 13.
- Replace each piece of essential hardware in your computer with an identical or equivalent spare piece of hardware (that you know is working), one component at a time, to determine which piece of hardware is causing your computer to not come on all the way. Test after each hardware replacement to determine which component is faulty.The average computer user doesn't have a collection of working spare computer parts at home or work. If you don't either, we advise you to revisit Step 12. A POST card is an inexpensive and more reasonable approach than stocking spare computer parts.
- Finally, if all else fails, you'll probably need to seek professional help from a computer repair service or from your computer manufacturer's technical support.Unfortunately, if you don't have a POST card or spare parts to swap in and out, you're left not knowing which piece of your essential PC hardware is faulty. In these cases, you have little option than to rely on the help of individuals or companies that do have these resources.
- Is your computer still not showing anything on the monitor? See Get More Help for information about contacting me on social networks or via email, posting on tech support forums, and more.
Did we miss a troubleshooting step that helped you (or might help someone else) fix a computer that's not showing anything on screen? Let us know and we'd be happy to include the information here.
![Motherboard Motherboard](https://visihow.com/images/4/49/Determine_if_Your_Motherboard_Is_Dead_63489.jpg)
Hi guys,
I just started my PC after a while & it turns ON, lights turn on, but there is NO Display on Monitor.
I did some research on Google about this issue & did a few things.
1). I removed all the hardware, except processor & power supply. Turned On, but same issue.
2). I tried after removing ram, & then by switching ram slot, but still no use.
3). I removed my HD 3450 512MB graphics card & plugged monitor in Built-In Monitor port & Vica versa (In Graphics Card), but no use.
4). I removed hard disk & DVD rom & changed their power cords, but no use.
5). I removed the computer cord, & pressed & hold the 'ON' button for 30 to 60 seconds, but no use.
It was working fine a couple of weeks ago, but then I turned on & it was not working anymore. By the way, when I turned on it acted a little weird before going dark. Actually when I turned on, it took a long time to get to display & then window was also working weird, then I restarted a couple of time & I though it was my hard disk, (who sometimes have power cord issue that works fine if we change it, but its not that).
Any idea how to fix this issue or what is wrong with my computer?
Thanks.
I just started my PC after a while & it turns ON, lights turn on, but there is NO Display on Monitor.
I did some research on Google about this issue & did a few things.
1). I removed all the hardware, except processor & power supply. Turned On, but same issue.
2). I tried after removing ram, & then by switching ram slot, but still no use.
3). I removed my HD 3450 512MB graphics card & plugged monitor in Built-In Monitor port & Vica versa (In Graphics Card), but no use.
4). I removed hard disk & DVD rom & changed their power cords, but no use.
5). I removed the computer cord, & pressed & hold the 'ON' button for 30 to 60 seconds, but no use.
It was working fine a couple of weeks ago, but then I turned on & it was not working anymore. By the way, when I turned on it acted a little weird before going dark. Actually when I turned on, it took a long time to get to display & then window was also working weird, then I restarted a couple of time & I though it was my hard disk, (who sometimes have power cord issue that works fine if we change it, but its not that).
Any idea how to fix this issue or what is wrong with my computer?
Thanks.